Normal view

There are new articles available, click to refresh the page.
Before yesterdayMain stream

DFRobot EDGE102-DMX512 lighting controller combines ESP32-S3 MCU and DMX512 protocol chip

20 November 2024 at 00:01
EDGE102 DMX512 Lighting Programming Controller

DFRobot’s EDGE102-DMX512 is a DMX512 lighting programming controller based on ESP32-S3 wireless MCU designed for efficient management of stage, theater, and venue lighting. With integrated WiFi and Bluetooth, the controller supports wireless programming and control, simplifying the setup of advanced lighting systems. It offers RS485 (master/slave modes) interfaces, I2C, UART, and GPIO pins for compatibility with a wide range of sensors and boards. This controller enables automation through sensor integration, supporting devices such as infrared detectors, sound level meters, and laser sensors. Its eight optically isolated industrial switch inputs ensure seamless compatibility with PNP sensors, allowing lighting effects to respond automatically to environmental inputs. By reducing dependence on manual DMX consoles, it is well-suited for automated lighting in theaters, stages, and commercial venues. EDGE102-DMX512 specifications: SoC – Espressif ESP32-S3 CPU – Dual-core Tensilica LX7 up to 240 MHz with vector instructions for AI acceleration Memory – 512 KB of internal [...]

The post DFRobot EDGE102-DMX512 lighting controller combines ESP32-S3 MCU and DMX512 protocol chip appeared first on CNX Software - Embedded Systems News.

EDATEC ED-GWL1010: Amlogic S905X4-based PoE-enabled LoRaWAN gateway targets Smart Buildings and IoT applications

14 November 2024 at 12:00
ED-GWL1010 LoRaWAN gateway

The AMLogic S905X4 SoC is typically found in TV boxes, but EDATEC has integrated the quad-core Cortex-A55 SoC into its ED-GWL1010 LoRaWAN IoT gateway designed for smart buildings and industrial IoT networks requiring long-range, low-power connectivity. The ED-GWL1010 is built around the ED-REIMEI1 single-board computer, combining a mainboard and an expansion board. It integrates Semtech’s latest SX1302/SX103 baseband chip and a Microchip ATECC608 security chip for enhanced protection. The gateway offers up to 8GB LPDDR4 and 32GB of eMMC storage. For connectivity, it supports dual-band WiFi, Bluetooth 5.0, 10/100Mbps Ethernet with PoE, and a mini PCIe slot for a LoRa module compatible with both American and European LoRa frequencies (US915, AU915, AS923, EU868). It also features USB 3.0, an RGB LED indicator, a user button, and flexible power options through a 7-18V DC input or PoE. The ED-GWL1010 operates reliably in temperatures ranging from -25°C to 50°C and is housed [...]

The post EDATEC ED-GWL1010: Amlogic S905X4-based PoE-enabled LoRaWAN gateway targets Smart Buildings and IoT applications appeared first on CNX Software - Embedded Systems News.

Seeed Studio’s XIAO MG24 and XIAO MG24 Sense boards target battery-powered Matter and BLE applications

2 November 2024 at 10:13
Seeed Studio XIAO MG24

Seeed Studio has added two members to its XIAO family of tiny MCU boards with the XIAO MG24 and XIAO MG24 Sense boards based on Silicon Labs EFR32MG24 multi-protocol wireless SoC and designed for battery-powered Matter over Thread and Bluetooth LE 5.3 applications. Both 21×17.8 mm USB-C boards feature a 78MHz Silabs MG24 Cortex-M33 microcontroller with 256kB SRAM and 1536KB flash, an additional 4MB SPI flash on-board, and 22 pins and pads for GPIO pins, analog inputs, and power signals, plus a reset button and two LEDs. The “Sense” model adds an analog microphone and a 6-axis IMU sensor. XIAO MG24/MG24 Sense specifications: SoC – Silicon Labs EFR32MG24 (EFR32MG24B220F1536IM48-B) MCU cores Arm Cortex-M33 @ 78.0 MHz with DSP instruction and floating-point unit for user application Arm Cortex-M0+ core for wireless Memory – 256 KB RAM Storage – 1536 KB flash Wireless protocols – Matter, OpenThread, Zigbee, Bluetooth Low Energy 5.3, [...]

The post Seeed Studio’s XIAO MG24 and XIAO MG24 Sense boards target battery-powered Matter and BLE applications appeared first on CNX Software - Embedded Systems News.

OpenUC2 10x is an ESP32-S3 portable microscope with AI-powered real-time image analysis

29 October 2024 at 00:01
Seeed Studio OpenUC2 10x AI Microscope

Seeed Studio has recently launched the OpenUC2 10x AI portable microscope built around the XIAO ESP32-S3 Sense module. Designed for educational, environmental research, health monitoring, and prototyping applications this microscope features an OV2640 camera with a 10x magnification with precise motorized focusing, high-resolution imaging, and real-time TinyML processing for image handling. The microscope is modular and open-source making it easy to customize and expand its features using 3D-printed parts, motorized stages, and additional sensors. It supports Wi-Fi connectivity with a durable body, uses USB-C for power and swappable objectives make it usable in various applications. Previously we have written about similar portable microscopes like the ioLight microscope and the KoPa W5 Wi-Fi Microscope, and Jean-Luc also tested a cheap USB microscope to read part number of components. Feel free to check those out if you are looking for a cheap microscope. OpenUC2 10x specifications: Wireless MCU – Espressif Systems ESP32-S3 CPU [...]

The post OpenUC2 10x is an ESP32-S3 portable microscope with AI-powered real-time image analysis appeared first on CNX Software - Embedded Systems News.

Waveshare ESP32-S3 ETH board provides Ethernet and camera connectors, supports Raspberry Pi Pico HATs

28 October 2024 at 13:00
ESP32 S3 ETH CAM KIT ESP32 S3 ETH Development Board with OV2640 camera support

Waveshare has recently launched the ESP32-S3-ETH development board with an Ethernet RJ45 jack, a camera interface, and compatibility with Raspberry Pi Pico HAT expansion boards. This board includes a microSD card interface and supports OV2640 and OV5640 camera modules. Additionally, it offers an optional Power over Ethernet (PoE) module, making it ideal for applications such as smart home projects, AI-enhanced computer vision, and image acquisition. Previously, we have written about LILYGO T-ETH-Lite, an ESP32-S3 board with Ethernet and optional PoE support. We have also written about LuckFox Pico Pro and Pico Max, Rockchip RV1106-powered development boards with 10/100M Ethernet and camera support. The ESP32-S3-ETH board is like a combination of those two, where you get an ESP32-S3 microcontroller, Ethernet (with optional PoE), and a camera interface. ESP32-S3 ETH development board specifications: Wireless module ESP32-S3R8 MCU – ESP32-S3 dual-core LX7 microprocessor @ up to 240 MHz with Vector extension for machine learning Memory – 8MB PSRAM Storage [...]

The post Waveshare ESP32-S3 ETH board provides Ethernet and camera connectors, supports Raspberry Pi Pico HATs appeared first on CNX Software - Embedded Systems News.

NVIDIA Jetson Orin NX development kit comes with up to 16GB RAM, 128GB NVMe SSD, WiFi 5

25 October 2024 at 07:00
Jetson Orin NX AI Development Kit

Waveshare’s Jetson Orin NX Development Kit is an AI edge computing platform tailored for robotics and AI-driven applications built around the NVIDIA Jetson Orin NX module 8GB/16GB delivering up to 70 TOPS and 100 TOPS of AI performance, respectively. It features the JETSON-ORIN-IO-BASE base board, which provides essential interfaces like an M.2 socket, DisplayPort (DP) video output, and USB ports, making it easy for users to connect multiple sensors and peripherals for high-performance AI tasks. The kit includes a 128GB NVMe SSD for high-speed storage and comes pre-installed with the AW-CB375NF wireless network card, which supports dual-band Wi-Fi 5 and Bluetooth 5.0. The Jetson Orin NX module operates within a configurable power range of 10W to 25W, delivering up to 5x the performance of the Jetson Xavier NX module. This development kit is suitable for large-scale AI projects requiring multiple concurrent inference pipelines and high-speed data processing. Previously, we covered [...]

The post NVIDIA Jetson Orin NX development kit comes with up to 16GB RAM, 128GB NVMe SSD, WiFi 5 appeared first on CNX Software - Embedded Systems News.

ESP32-S3 board features 1.91-inch AMOLED display and QMI8658 6-axis motion sensor

22 October 2024 at 17:00
ESP32-S3 Touch AMOLED 1.91

Waveshare has launched an ESP32-S3 1.91-inch AMOLED development board with a 6-axis motion sensor designed for the rapid prototyping of IoT and portable projects with interactive displays. The board is built around the ESP32-S3R8 chip, featuring a 32-bit LX7 dual-core processor running at up to 240MHz, with integrated 2.4GHz Wi-Fi and Bluetooth BLE 5. It also includes 16MB Flash, 8MB PSRAM, 512KB SRAM, and 384KB ROM for efficient processing and memory management. At the core of its display capabilities is a 1.91-inch AMOLED screen with a 240×536 resolution, supporting 16.7 million colors. Powered by the RM67162 controller and connected via the QSPI interface, the display is ideal for running GUI applications like LVGL. The board is available in both touch and non-touch versions, with the touch-enabled models using the FT3168 touch IC. Other features include a QMI8658 6-axis IMU, a microSD card slot, and a Lithium battery header. The ESP32-S3 [...]

The post ESP32-S3 board features 1.91-inch AMOLED display and QMI8658 6-axis motion sensor appeared first on CNX Software - Embedded Systems News.

Seeed Studio launches ESP32-C6-powered 60GHz mmWave human fall detection and breathing/heartbeat detection sensor kits

21 October 2024 at 07:00
mmWave human fall detection and heartbeat sensor

Last year, we reviewed the MR60FDA1 60GHz mmWave fall detection sensor kit, which utilizes the XIAO ESP32C3 module as its core. This module, featuring both Wi-Fi and Bluetooth connectivity, opens up various IoT applications. Now, Seeed Studio has introduced advanced mmWave sensor modules specifically designed for enhanced fall detection and heartbeat monitoring. The MR60FDA2 is optimized for fall detection, while the MR60BHA2 is designed for heartbeat monitoring. Powered by an ESP32-C6 WiFi 6 and RIS-Bluetotoh LE microcontroller, these modules offer reliable detection for real-time fall monitoring and accurate heartbeat tracking. They also feature customizable RGB LEDs and ambient light sensors, providing additional flexibility. With expansion options via Grove GPIO ports, these versatile modules are well-suited for applications like smart home integration and healthcare monitoring. Previously, we covered the RoomSense IQ and the DesignCore RS-6843AOPU with mmWave technology. The RoomSense IQ is an ESP32-S3-based modular room monitor with mmWave radar presence [...]

The post Seeed Studio launches ESP32-C6-powered 60GHz mmWave human fall detection and breathing/heartbeat detection sensor kits appeared first on CNX Software - Embedded Systems News.

KAGA FEI ES4L15BA1 is an ultra-small Bluetooth LE 6.0 and 802.15.4 module based on Nordic nRF54L15 SoC

18 October 2024 at 09:01
ultra small Bluetooth 6.0 module

Japanese company KAGA FEI has recently unveiled the incredibly small ES5L15BA1 Bluetooth LE 6.0 and 802.15.4 module based on Nordic Semi nRF54L15 ultra-low-power Cortex-M33 wireless MCU. We had previously covered the u-Blox NORA-B2 which I already found pretty small at 14.3 x 10.4 x 1.9mm, but the ES5L15BA1 module goes a step further measuring just 8.55 x 3.25 x 1.00 mm with an integrated antenna which could make it the world’s smallest Bluetooth LE module. KAGA FEI ES4L15BA1 specifications: SoC – Nordic Semiconductor nRF54L15 MCU cores Arm Cortex-M33 with Arm TrustZone @ 128MHz RISC-V coprocessor for software-defined peripheral Memory – 256KB SRAM Storage – 1.5MB non-volatile memory Wireless Bluetooth 6.0 Data rates – 2Mbps, 1Mbps, 500kbps, 125kbps Features AoA / AoD Channel Sounding 802.15.4 radio for Thread / Zigbee / Matter Nordic Proprietary 2.4 GHz protocol up to 4 Mbps Frequency – 2402 to 2480 MHz +8dBm output power Antenna [...]

The post KAGA FEI ES4L15BA1 is an ultra-small Bluetooth LE 6.0 and 802.15.4 module based on Nordic nRF54L15 SoC appeared first on CNX Software - Embedded Systems News.

Synaptics Veros SYN4383 and SYN43756(E) SoCs support tri-band WiFi 6E, Bluetooth 5.3/5.4, and 802.15.4 connectivity

17 October 2024 at 21:19
Synaptics Veros S0YN4383 and SYN43756(E)

Synaptic has unveiled the SYN4383 and SYN43756(E) high-performance “Veros” SoCs with tri-band Wi-Fi 6E, Bluetooth 5.3/5.4, and an optional 802.15.4 radio. The SYN4383 is an upgrade to SYN4382 SoC that supports 1,200 Mbps 2×2 MIMO Wi-Fi 6E, Bluetooth 5.4, and 802.15.4 for Zigbee and Thread support. It supports real simultaneous dual-band (RSDB) operation and offers “greater system integration”. The SYN43756(E) is similar but lacks an 802.15.4 radio and RSDB support. SYN4383 “Triple Combo 3” Wi-Fi 6E, Bluetooth 5.4, 802.15.4 SoC Synaptics Veros SYN4383 key features: Tri-band 2×2 MIMO Wi-Fi 6E (802.11ax) up to 1200 Mbps throughput, RSDB with 2.4 GHz radio and either 5 or 6 GHz radio, and support for legacy 802.11a/b/g/n/ac WiFi Bluetooth 5.4 (Bluetooth 6.0 compatible) with LE Audio, Channel Sounding for accurate positioning 802.15.4 radio for Thread and Zigbee Application-layer support for Matter-compliant security and interoperability Smart Co-Ex for WiFi/Bluetooth coexistence in the 2.4 GHz band [...]

The post Synaptics Veros SYN4383 and SYN43756(E) SoCs support tri-band WiFi 6E, Bluetooth 5.3/5.4, and 802.15.4 connectivity appeared first on CNX Software - Embedded Systems News.

LumenRadio’s nRF52840 based Wireless Modbus module aims to simplify Modbus RTU installations

15 October 2024 at 07:00
LumenRadio's W Modbus and W Modbus PRO module's

LumenRadio has recently introduced a Wireless Modbus (W-Modbus) module built around Nordic Semiconductor’s nRF52840 SoC. The module can connect up to 100 nodes, integrates a power amplifier with 100mW transmission power, and supports Bluetooth LE for smartphone connectivity. These features simplify Modbus RTU installations by eliminating traditional control cables, making them ideal for building and industrial automation applications. The company mentions two variants available for this module the ‘W-Modbus OEM Module’ which supports one Modbus client, and the ‘W-Modbus PRO OEM Module’ supporting up to sixteen Modbus clients. Both modules support self-healing, self-organizing mesh protocols that address the issues of network reliability and scalability in industrial environments. The module can also be used for remote monitoring and troubleshooting via smartphones. LumenRadio’s Wireless Modbus module specification Module – LumenRadio W-Modbus module SoC –  Nordic Semiconductor nRF52840 CPU – 32-bit Cortex-M4 core with FPU @ 64 MHz Connectivity Bluetooth 5.4  (BLE, Bluetooth mesh, [...]

The post LumenRadio’s nRF52840 based Wireless Modbus module aims to simplify Modbus RTU installations appeared first on CNX Software - Embedded Systems News.

Infineon XENSIV game controller features PSoC 6 MCU, magnetic sensors, and OPTIGA Trust M security

14 October 2024 at 17:33
Infineon XENSIV Game Controller

Infineon Technologies XENSIV game controller is a reference design that integrates XENSIV magnetic position sensors for precise joystick control without sensor drift and XENSIV Hall switch triggers for reliable operation. The controller also features capacitive CAPSENSE buttons, CAPSENSE presence detection, and a SPIDER+ rumble driver. These components work together with the PSoC 6 BLE microcontroller to create a low-power, plug-and-play solution. The onboard display allows users to monitor joystick movements, connection status, configurations, and battery information. The controller connects to PCs or smartphones as a USB human interface device (HID) without requiring manual configuration or driver installation. It also supports Bluetooth Low Energy and uses capacitive presence detection to optimize battery life. The design includes a PSoC 6 debugger and supports customizable shields providing flexibility for software and hardware integration. Previously, we covered an Arduino Nano Matter-powered game controller that successfully ported Quake, a popular first-person shooter game. We’ve also [...]

The post Infineon XENSIV game controller features PSoC 6 MCU, magnetic sensors, and OPTIGA Trust M security appeared first on CNX Software - Embedded Systems News.

AirCard Pro and AirNotch Pro Bluetooth trackers support Google/Apple network integration (Crowdfunding)

11 October 2024 at 08:37
AirCard Pro and AirNotch Pro Bluetooth trackers

Rolling Square introduces its latest Bluetooth trackers – AirNotch Pro and AirCard Pro – designed for use with personal items like keys, wallets, bags, and more. Both trackers are designed for portability, and the AirNotch Pro is designed as a keyring, while the AirCard Pro suits wallets with a thinner, credit card-like design. The products integrate into Apple and Google’s tracking networks, with some features currently limited to Apple. Previously, we covered the SenseCAP T1000, a credit card-sized LoRaWAN GPS tracker powered by Semtech’s LR1110. Several years ago we covered some Bluetooth beacons such as the Puck.js or RuuviTag, but we have yet to explore Bluetooth-only trackers with wireless charging capabilities. Rolling Square AirCard Pro Bluetooth trackers AirCard Pro technical features: Network White version – Operates on Google’s Android Find My Device network (Android 6 or above) Black version – Operates on Apple Find My network (iOS 14 or above) [...]

The post AirCard Pro and AirNotch Pro Bluetooth trackers support Google/Apple network integration (Crowdfunding) appeared first on CNX Software - Embedded Systems News.

Taoglas AntJack is an RJ45 jack-mounted Wi-Fi antenna for Bluetooth, Wi-Fi 6/6E, and Wi-Fi 7

9 October 2024 at 18:57
Taoglas Wi FI antenna on jack

Dublin-based Taoglas has unveiled the AntJack described as “an industry-first Wi-Fi antenna for an RJ45 Jack”. The AntJack, also known as the FXM100, can be mounted on any standard RJ45 Ethernet connector to create a 2-in-1 solution that saves space and enhances wireless performance across 2.4 GHz, 5.8 GHz, and 7.1 GHz frequency bands. It is a compact (26.6 x 15.6 x 13.1 mm), omnidirectional dipole antenna with support for Bluetooth, Wi-Fi 6/6E, and Wi-Fi 7. It can be used in various applications, such as modems and routers, industrial gateways, factory automation, industrial robotics, and test and measurement systems. The AntJack is especially well-suited for embedded applications with space constraints and positioning challenges such as 4 x 4 or 8 x 8 MIMO configurations. It features an easy “peel and stick” design manufactured from flexible PCB material with adhesive conductive foam, allowing straightforward installation on RJ45 connectors. According to Oliver [...]

The post Taoglas AntJack is an RJ45 jack-mounted Wi-Fi antenna for Bluetooth, Wi-Fi 6/6E, and Wi-Fi 7 appeared first on CNX Software - Embedded Systems News.

Pimoroni Pico Plus 2 W combines RP2350B MCU with Raspberry Pi RM2 Wi-Fi and Bluetooth module

5 October 2024 at 15:11
Pimoroni Pico Plus 2 W

Raspberry Pi released the Raspberry Pi Pico 2 a few months ago, featuring the new RP2350 chip. Despite several upgrades, it lacks wireless connectivity like Pico W. While there’s no official Raspberry Pi Pico 2 W yet, Pimoroni has developed an unofficial alternative, the Pimoroni Pico Plus 2 W, which integrates Wi-Fi and Bluetooth using a yet-to-be-formally-announced Raspberry Pi RM2 module and potentially set to appear in a future Pico 2W. The Pimoroni Pico Plus 2W board is powered by the Raspberry Pi RP2350B dual-core Arm Cortex-M33 microcontroller, features 16MB of QSPI flash with XiP support, 8MB of PSRAM, wireless connectivity, a USB Type-C port for power and data, and a Qwiic/STEMMA QT connector for breakout board integration. A few days ago, we covered the Pimoroni Explorer board, an electronic prototyping board built around the Raspberry Pi RP2350B chip. It features a 2.8-inch LCD screen, a speaker connector, and multiple [...]

The post Pimoroni Pico Plus 2 W combines RP2350B MCU with Raspberry Pi RM2 Wi-Fi and Bluetooth module appeared first on CNX Software - Embedded Systems News.

UnifyDrive UT2 – A compact NAS powered by Rockchip RK3588C with NVMe SSD support and AI-driven storage management (Crowdfunding)

2 October 2024 at 09:00
UnifyDrive UT2 NAS

The UnifyDrive UT2 is a compact network-attached storage (NAS) device powered by the Rockchip RK3588C processor. It supports WiFi 6, and Bluetooth, and has multiple ports for connectivity. Equipped with two M.2 2280 slots for PCIe 3.0 NVMe SSDs, it offers up to 16 TB of storage. The device can connect to networks via 2.5 GbE or WiFi and also function as a WiFi access point, allowing file transfers even without an internet connection. A built-in battery provides uninterruptible power supply (UPS) functionality, enabling continued operation when unplugged. Designed for both home and mobile use, the UnifyDrive UT2 offers AI-driven storage management in a portable form factor. Its versatile networking options allow remote access, backups, and on-the-go file transfers. Despite its size, it delivers robust functionality, serving as a full-featured NAS solution in a variety of settings. I didn’t find any significant differences between the Rockchip RK3588 and RK3588C. This [...]

The post UnifyDrive UT2 – A compact NAS powered by Rockchip RK3588C with NVMe SSD support and AI-driven storage management (Crowdfunding) appeared first on CNX Software - Embedded Systems News.

Raytac AN7002Q – A smaller nRF7002 Wi-Fi 6 module for industrial IoT applications

28 September 2024 at 08:28
AN7002Q-P module

IoT solutions company Raytac has introduced the AN7002Q Wi-Fi 6 module series, which integrates Nordic Semiconductor’s nRF7002 chipset and is designed for Industrial IoT, smart home, healthcare, consumer electronics, and automotive applications. They can be paired with Raytac’s MDBT53 Bluetooth LE modules based on the nRF5340 multiprotocol SoC, supporting Wi-Fi and Bluetooth LE solutions. The AN7002Q is a low-power Wi-Fi 6 module supporting dual-band 2.4 GHz and 5 GHz operation with a maximum PHY data rate of 86 Mbps (MCS7). It is compatible with IEEE 802.11ax, a/b/g/n/ac standards, and connects to a host SoC or MCU via SPI or QSPI interfaces. The module also supports coexistence with Bluetooth LE, Thread, and Zigbee systems, making it ideal for IoT applications. Previously, we covered the Abluetech PTR7002, a low-power wireless module based on the Nordic Semiconductor nRF7002. The PTR7002 has a slightly larger size and offers more GPIO options, while the AN7002Q [...]

The post Raytac AN7002Q – A smaller nRF7002 Wi-Fi 6 module for industrial IoT applications appeared first on CNX Software - Embedded Systems News.

ESP32-C6 WiFi 6 and Bluetooth 5.0 USB-C development board integrates 1.47-inch TFT LCD Display

24 September 2024 at 00:01
ESP32-C6-LCD-1.47

Waveshare has introduced the ESP32-C6-LCD-1.47 development board powered by an ESP32-C6 RISC-V microcontroller with WiFi 6 and Bluetooth 5 connectivity and equipped with a 1.47-inch display with a 172×320 resolution. With a 4MB flash, an RGB LED, and a microSD card slot for extra storage, this board is suitable for projects that need a compact display, low power consumption, and wireless connectivity such as AIoT applications and human-machine interfaces (HMI). Earlier this month, we covered the ESP32-S3 USB dongle, another development board from Waveshare designed for HMI applications with the same 1.47-inch display with a 172×320 resolution, but a USB Type-A port instead of the USB-C port found in the model covered today. In the past, we’ve written about other ESP32-based development boards for HMI applications, including the LILYGO T-HMI, ESP32-S3-Touch-LCD-4.3B, and Waveshare’s ESP32-S3 LCD Driver Board supporting both square and round displays. Feel free to check them out if [...]

The post ESP32-C6 WiFi 6 and Bluetooth 5.0 USB-C development board integrates 1.47-inch TFT LCD Display appeared first on CNX Software - Embedded Systems News.

M5Stack ESP32-S3-Pico-based devkits: ATOMS3R with 0.85-inch color display, and ATOMS3R Cam with VGA camera

21 September 2024 at 10:00
ATOMS3R ESP32-S3-Pico devkit

M5Stack ATOMS3R and ATOMS3R Cam are two tiny devkits based on ESP32-S3-Pico system-in-package and a similar design but the first one features a 0.85-inch color color IPS display, while the other is equipped with a GC0308 VGA camera. Both modules measure just 24x24mm with a thickness of around 13mm, integrate BMM150 and BMI270 motion sensors, offer GPIO expansion through female headers and a grove connector, and feature an infrared transmitter and a USB Type-C port for power and programming. Those are the second devkits based on the ESP32-S3-Pico SiP after we covered the tiny OMGS3 module earlier this week. M5Stack ATOMS3R with display ATOMS3R specifications: SiP – Espressif ESP32-S3-PICO-1-N8R8 SoC ESP32-S3 dual-core Tensilica LX7 up to 240 MHz with 512KB SRAM, 16 KB RTC SRAM Wireless – WiFi 4 and Bluetooth 5 LE + Mesh Memory – 8MB QSPI PSRAM Storage – 8MB QSPI flash Display – 0.85-inch color IPS screen [...]

The post M5Stack ESP32-S3-Pico-based devkits: ATOMS3R with 0.85-inch color display, and ATOMS3R Cam with VGA camera appeared first on CNX Software - Embedded Systems News.

❌
❌